The Pratt & Whitney F135 is an afterburning turbofan developed for the Lockheed Martin F-35 Lightning II, a single-engine strike fighter. The F135 family has several distinct variants; a conventional, forward thrust variant and a multi-cycle Short Take-Off Vertical Landing STOVL variant that includes a forward lift fan. The first production engines were delivered in 2009.
Developed from the Pratt & Whitney F119 engine used on the F-22 Raptor, the F135 produces around 40,000 lbf of thrust. The F135 competed with the General Electric/Rolls-Royce F136 to power the F-35.
Video Pratt & Whitney F135
Development
The F135 originated with Lockheed Corporation Skunk Works, with efforts to develop a stealthy STOVL strike fighter for the U.S. Marine Corps under a 1986 DARPA program. Lockheed employee Paul Bevilaqua developed and patented a concept aircraft and propulsion system, and then turned to Pratt & Whitney (P&W) to build a demonstrator engine. The demonstrator used the first stage fan from a F119 engine for the lift fan. The engine fan and core from the F100-220 were used for the core of the demonstrator engine, and the larger low-pressure turbine from the F100-229 was used for the low-pressure turbine of the demonstrator engine. The larger turbine was used to provide the additional power required to operate the lift fan. Finally, a variable thrust deflecting nozzle was added to complete the "F100-229-Plus" demonstrator engine. This engine proved the lift-fan concept and led to the development of the current F135 engine.
The F135 team is made up of Pratt & Whitney, Rolls-Royce and Hamilton Sundstrand. Pratt & Whitney is the prime contractor for the main engine, and systems integration. Rolls-Royce is responsible for the vertical lift system for the STOVL aircraft. Hamilton Sundstrand is responsible for the electronic engine control system, actuation system, PMAG, gearbox, and health monitoring systems. Woodward, Inc. is responsible for the fuel system.
P&W developed the F135 from their F119 turbofan, which powers the F-22 Raptor, as the "F119-JSF". The F135 integrates the F119 core with new components optimized for the JSF. The F135 is assembled at a plant in Middletown, Connecticut. Some parts of the engine are made in Longueuil, Quebec, Canada, and in Poland.
The first production propulsion system for operational service was scheduled for delivery in 2007 with the purpose of serving the U.S., UK, and other international customers. The initial F-35s went into production with the F135 engines, but the GE/Rolls-Royce team planned to develop a replacement F136 engine in July 2009. In 2010, the Pentagon planned for the two propulsion systems to be competitively tendered. However, since 2006 the Defense Department has not requested funding for the alternate F136 engine program, but Congress has maintained program funding.
As of 2009, P&W developed a more durable version of the F135 engine to increase the service life of key parts. The life expectancy of the parts was reduced because the hot sections of the engine (combustor and high-pressure turbine blades specifically) ran hotter than expected. The test engine is designated XTE68/LF1, and testing is expected to begin in 2010. This redesign has caused "substantial cost growth."
P&W expects to deliver the F135 below the cost of the F119, even though it is a more powerful engine. However, in February 2013 a cracked turbine blade was found during a scheduled inspection. The crack was caused by operating at high turbine temperatures for longer periods than usual. In December 2013 the hollow first stage fan blisk failed at 77% of its expected life during a ground test. It will be replaced by a solid part adding 6 lb (2.7 kg) in weight. In 2013, a former P&W employee was caught attempting to ship "numerous boxes" of sensitive information about the F135 to Iran.
Despite the troubles, the 100th engine was delivered in 2013. LRIP-6 was agreed in 2013 for $1.1 billion for 38 engines of various types, which helped to decrease the unit cost.
Air Force Lt. Gen. Christopher C. Bogdan, the executive officer of the F-35 program, has called out P&W for falling short on manufacturing quality of the engines and slow deliveries. His deputy director Rear Admiral Randy Mahr said that P&W stopped their cost cutting efforts after "they got the monopoly". In 2013 the price of the F135 increased by $4.3 billion.
In May 2014, Pratt & Whitney discovered conflicting documentation about the origin of titanium material used in some of its engines, including the F135. The company assessed that the uncertainty did not pose a risk to safety of flight but suspended engine deliveries as a result. Bogdan supported P&W's actions and said the problem was now with A&P Alloys, the supplier. The US Defense Contract Management Agency wrote in June 2014 that Pratt & Whitney's "continued poor management of suppliers is a primary driver for the increased potential problem notifications." A&P Alloys stated that they stood behind their product even though they were not given access to the parts to do their own testing. Tracy Miner, an attorney with Boston-based Demeo LLP representing A&P Alloys said, "it is blatantly unfair to destroy A&P's business without allowing A&P access to the materials in question"
In July 2014 there was an uncontained failure of a fan rotor while the aircraft was preparing for take-off. The parts passed through a fuel tank and caused a fire, grounding the F-35 fleet. During high g-force maneuvering three weeks before flight, there was excessive rubbing at the seal between the fan blisk and the fan stator causing the failure. The engine "flex" generated a temperature of over 1,000 °C (1,900 °F) in materials designed to fail at 540 °C (1,000 °F). Micro cracks appeared in third-stage fan blades, according to program manager Christopher Bogdan, causing blades to separate from the disk. The failed blades punctured the fuel cell and hot air mixing with jet fuel caused the fire. As a short term fix, each aircraft is flown on a specific flight profile to allow the rotor seal to wear a mating groove in the stator to prevent excessive rubbing.
Pratt & Whitney managed to meet their 2015 production goals, but "recurring manufacturing quality issues" in turbine blades and electronic control systems required engines to be pulled from the fleet.
Maps Pratt & Whitney F135
Design
Derived from the F119 engine, the F135 is a mixed-flow afterburning turbofan consisting of a new fan and LP turbine.
There are 3 F135 variants: the -100 engine, -400 engine, and the -600 engine. The -400 is similar to the -100, the major difference being the use of salt-corrosion resistant materials. The -600 is described below with an explanation of the engine configuration changes that take place for hovering. The engine and Rolls-Royce LiftSystem make up the Integrated Lift Fan Propulsion System (ILFPS).
The lift for the STOVL version in the hover is obtained from a 2-stage lift fan (about 46%) in front of the engine, a vectoring exhaust nozzle (about 46%), and a nozzle in each wing using fan air from the bypass duct (about 8%). These relative contributions to the total lift are based on thrust values of 18,680 lb, 18,680 lb and 3,290 lb respectively. Another source gives thrust values of 20,000 lb, 18,000 lb and 3,900 lb respectively.
In this configuration most of the bypass flow is ducted to the wing nozzles, known as roll posts. Some is used for cooling the rear exhaust nozzle, known as the 3-bearing swivel duct nozzle (3BSD). At the same time an auxiliary inlet is opened on top of the aircraft to provide additional air to the engine with low distortion during the hover.
The LP turbine drives the lift fan through a shaft extension on the front of the LP rotor and a clutch. The engine operates as a separate flow turbofan with a higher bypass ratio. The power to drive the fan (about 30,000 SHP) is obtained from the LP turbine by increasing the hot nozzle area.
A higher bypass ratio increases the thrust for the same engine power as a fundamental consequence of transferring power from a small diameter propelling jet to a larger diameter one. When the F135 is in the hover using its increased bypass ratio, the thrust augmentation decreases to 50% with no increase in fuel flow. Thrust augmentation increases to 52% in horizontal flight when using the afterburner, but with a large increase in fuel flow.
The transfer of approximately 1/3 of the power available for hot nozzle thrust to the lift fan reduces the temperature and velocity of the rear lift jet impinging on the ground. The F-35 can achieve a limited 100% throttle cruise without afterburners of Mach 1.2 for 150 miles.
Improving engine reliability and ease of maintenance is a major objective for the F135. The engine has fewer parts than similar engines, which improves reliability. All line-replaceable components (LRCs) can be removed and replaced with a set of six common hand tools. The F135's health management system is designed to provide real time data to maintainers on the ground. This allows them to troubleshoot problems and prepare replacement parts before the aircraft returns to base. According to Pratt & Whitney, this data may help drastically reduce troubleshooting and replacement time, as much as 94% over legacy engines.
Planned improvements
Although no service has issued a requirement for an upgraded engine, Pratt and Whitney is cooperating with the US Navy on a two-block improvement plan for the F135 engine. The goals of Block 1 are a 7-10% increase in thrust and a 5-7% lower fuel burn. The plans include better cooling technology for turbine blades; this would increase the longevity of the engine and substantially reduce maintenance costs. The goal of Block 2 is to work with the US Air Force's Adaptive Engine Transition Program, with the intention of introducing technology for an engine rated at 45,000 lb of thrust, to be used in a sixth-generation fighter. At the end of May 2017 Pratt and Whitney announced the F135 Growth Option 1 had finished testing and was available for production. The upgrade requires the changing of the power module on older engines and can be seamlessly inserted into future production engines at a minimal increase in unit cost and no impact to delivery schedule. The Growth Option 1 offers a improvement of 6-10% thrust across the F-35 flight envelope while also getting a 5-6% fuel burn reduction.
Variants
- F135-PW-100 : Used in the F-35A Conventional Take-Off and Landing variant
- F135-PW-400 : Used in the F-35C carrier variant
- F135-PW-600 : Used in the F-35B Short Take-Off Vertical Landing variant
Applications
- Lockheed Martin F-35 Lightning II
Specifications (F135-PW-100)
Data from F135engine.com
General characteristics
- Type: afterburning turbofan
- Length: 220 in (559 cm)
- Diameter: 46 in (117 cm) max., 43 in (109 cm) at the fan inlet
- Dry weight: 3,750 lb (1,701 kg)
Components
- Compressor: 3-stage fan, 6-stage high-pressure compressor
- Combustors: annular combustor
- Turbine: 1-stage high-pressure turbine, 1-stage low-pressure turbine
Performance
- Maximum thrust: 43,000 lbf (190 kN) max., 28,000 lbf (125 kN) intermediate
- Overall pressure ratio: 28:1 overall pressure ratio
- Thrust-to-weight ratio: 7.47:1 (dry), 11.467:1 (wet/afterburning)
Specifications (F135-PW-600)
Data from F135engine.com
General characteristics
- Type: Afterburning Turbofan with shaft driven remote lift fan
- Length: 369 in (937.3 cm)
- Diameter: 46 in (116.8 cm) maximum, 43 in (109.2 cm) fan inlet, 53 in (134.6 cm) lift fan inlet
- Dry weight:
Components
- Compressor: 3 stage fan, 6 stage high-pressure compressor, 2 stage, contra-rotating, shaft driven lift fan
- Combustors: annular combustor
- Turbine: Single stage high pressure turbine, 2-stage low pressure turbine
Performance
- Maximum thrust: 41,000 lbf (182 kN) max, 27,000 lbf (120 kN) intermediate, 40,650 lbf (180.8 kN) hover
- Overall pressure ratio: 28:1 overall pressure ratio (conventional), 29:1 overall pressure ratio (powered lift),
- Power-to-weight ratio:
See also
- Rolls-Royce LiftSystem
- Related development
- Pratt & Whitney F119
- Comparable engines
- General Electric/Rolls-Royce F136
- Related lists
- List of aircraft engines
References
- Bibliography
External links
- Pratt & Whitney F135 page
- www.jsf.mil: F135 gallery
Source of the article : Wikipedia
0 Comments